Yes! I confirmed with Lippert that the Lippert Ignition Proof 5th Wheel RV Landing Gear w/Harness # LC145236 will work as a replacement switch on your 2021 XLR12 Boost Toy Hauler. view full answer...
As the FMSMA15-SS has been discontinued, I could not confirm the size of the exhaust filter that fits it, unfortunately. However, I can confirm that the Replacement Ventilation Exhaust Filter for Furrion Over the Range RV Convection Microwave # FR54FR will measure (approximately) 5-1/4" x 7-3/4".
I can also say that the Furrion Over the Range RV Convection Microwave # FMCM15SS is the direct replacement for the FMSMA15-SS. As the # FR54FR is a direct fit for the # FMCM15SS, it is safe to... view full answer...
The adjustments for the Equal-i-zer Weight Distribution Systems like part # EQ37120ET will pertain to adding and removing washers from the head to try and get the spring arms as parallel with the trailer frame as possible. However, this may not completely level your vehicle. The majority of these systems are only designed to gain back half of what you lost and since your vehicle is lifted, there is an even greater chance that the vehicle will not be completely level.
If you still seek... view full answer...
Since the weight distribution hitch head you have is only rated to 1200lbs tongue weight, then you will need to either reduce the tongue weight of your trailer below 1200lbs, or will need to replace the hitch with one that is rated above 1200lbs.
For a system rated over 1200lbs I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 14,000 lbs GTW, 1,400 lbs TW # EQ37140ET which works with tongue weights between 1000-1400lbs and would be perfect for your tongue... view full answer...
The Replacement Lid # A10-3376 can be used as a replacement for the MaxxFan RV roof vent you have now. It is more of a universal design so it would have a slightly more involved install but it's not too crazy. view full answer...
Thanks for letting me know the axle capacity of your 2018 Forest River XLR. With that info we know that the SumoSpring kit part # SS26MV that you referenced is the correct kit for it. view full answer...
An E1 error code on your Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU # FR93FR means that it tried to ignite twice but didn't have the correct amount of gas pressure. First check to make sure your gas valves are fully open. If they are and you're still having issues it could indicate an issue with your regulator. You'll need to have a licensed technician check the pressure on the line and possibly replace your regulator to ensure you're getting 11" WC at the water... view full answer...
At this time the biggest hitch size we have weight distribution shanks for is the 2-1/2 inch hitch size like the part # C17132. Which you would have to then use a 2-1/2 inch to 3 inch hitch reducer part # BWRHXA2183. view full answer...
The Equal-I-zer Weight Distribution System I recommend for your 2013 Ford F-150 Super Crew 4x4 with 3.5L Eco Boost and your Grand Design 297 travel trailer is the Equal-i-zer # EQ37120ET based on the weights you gave. The WD system is rated based on total tongue weight which is the loaded tongue weight of your trailer along with any cargo behind the rear axle of your truck. This system is rated properly to accommodate your truck and your trailer within the max towing capacities of your... view full answer...
The short answer is Yes, bearing # 15123 is slightly larger and stronger than # LM67048 and they use different races which means they are not interchangeable.
Bearing 15123 uses race # 15245 which has an outer diameter of 2.441 inches and bearing LM67048 uses race # LM67010 which has an outer diameter of 2.328 inches. The size and strength differences are due to the fact that bearing # 15123 is used in a higher weight capacity hub. Bearing # 15123 is the outer bearing for a hub for a... view full answer...
The Aluminum Viking Series Vor Trailer Wheel part # AX02560655FPS is designed to be used with 60 degree tapered lug nuts like the Americana Trailer Wheel Lug Nut part # AM90049. This is the most standard degree of lug nut taper and most widely used. view full answer...
The Trailer Hub and Drum Assembly # AKHD-865-7-2-EZ-K does have the same bearings and seal that you would find for one that fits a 5,200 axle so it should work. Even though this is the case it is always best to double check before purchasing.
Pull your hub and verify that you have a # 25580 inner bearing, # 14125A outer bearing, and grease seal like part # GS-2250DL with an inner diameter (ID) of 2.25". If this is the case then you are good to go! If you can find parts numbers then simply... view full answer...
The best trailer hitch option for your Salem Hyperlite camper is going to be a multi-fit hitch like the Curt MultiFit # 13703 which fits the standard trailer frame styles that are 22 and 72 inches apart. view full answer...
Toy haulers actually carry their "toys" in the back of the trailer. I looked up your XLR Boost 27QB toy hauler and this is true for it as well. Because of this you wouldn't increase the tongue weight when loading the SXS. It's even possible the tongue weight might go down.
A weight distribution system would still be recommended since you are close to the capacity either way. The best system will be the Strait-Line part # RP66084 which has a tongue weight range of 600-1,200 lbs and features... view full answer...
Go To Results